印刷廠在印刷過程中，對油墨的要求非常的高，主要是因為它決定了印刷效果，而我們在使用的時候經常容易出現接皮現象，下面濟南印刷廠就給大家介紹一下出現這種現象的原因：

Printing factory in the printing process, the ink requirements are very high, mainly because it determines the printing effect, and we are often prone to skin phenomenon when using, Jinan printing factory will introduce the reasons for this phenomenon:

1、油墨中的連結料組分能夠和空氣中的氧發生氧化還原反應，于空氣中暴露時間過長當然就會被氧化，出現結皮現象。

1. The binders in the ink can react with oxygen in the air, which will be oxidized if exposed in the air for a long time.

2、墨輥結構不好，產生不流動的滯留部分。

2. The structure of ink roller is not good, resulting in stagnant part.

3、在墨斗中如果長時間不攪拌，會出現結皮現象：

3. If the ink bucket is not stirred for a long time, there will be skinning

在印刷過程中我們常講"三勤"其中勤攪墨斗中的墨便是很重要的一項，它能夠維持墨斗中油墨很好的流動性，其次這樣做能夠使表層的和內部的經常的交換，避免和空氣接觸的油墨總是同一部分。

In the printing process, we often talk about "three diligence". Among them, frequently stirring the ink in the ink bucket is a very important one. It can maintain the good fluidity of the ink in the ink bucket. Secondly, it can make the surface and interior exchange frequently, and avoid that the ink in contact with the air is always the same part.
                                          

4、印刷機長時間停機時：

4. When the printer stops for a long time:

①沒有清洗墨路，造成在墨輥和墨斗中結皮，在工作中一定注意當較長時間停機的時候要將墨路清洗干凈，當停機時間不是很長的時候，可以選擇在墨路上噴涂防結皮劑。

① If the ink path is not cleaned, it will cause skin formation in the ink roller and ink bucket. In the work, pay attention to clean the ink path when it is shut down for a long time, and spray anti skin agent on the ink path when it is not shut down for a long time.

②暫時不用的裸露在空氣中放置，時間一長表面就會出現厚厚的氧化膜。我們在印刷廠都會有這樣的經驗，當從墨盒或是墨桶中向外盛墨的時候。

② Temporarily not exposed in the air, a long time, the surface will appear thick oxide film. We all have this experience in printing factories, when filling ink from the ink cartridge or ink bucket.

5、要盡量的將表面保持一個平的狀態，這樣做的道理就是盡量減少油墨和空氣的接觸面積，這樣即使結膜后浪費也會盡可能的小。

5. To keep the surface as flat as possible, the reason is to minimize the contact area between ink and air, so that even after conjunctiva waste will be as small as possible.

6、再就是將剩下的用保護膜重新蓋上，阻斷與空氣的接觸，這樣也能很好的防止的結皮現象。

6. Then the rest is covered with protective film again to block the contact with the air, which can also prevent the skin formation.

印刷廠剛開始做印刷的時候經常出現油墨結皮的現象，所以我們大家在今后加工過程中要采取防止結皮的方法，生產質量提高了，會有很多客流量，從而我們的經濟效益和收益也就提高了。

At the beginning of printing, the phenomenon of ink crusting often occurs in printing plants, so we should take measures to prevent ink crusting in the future processing process. With the improvement of production quality, there will be a lot of customers, so our economic benefits and income will also be improved.

感謝您的閱讀，希望以上內容對您有所幫助，如您想了解更多精彩內容請點擊我們的官網：濟南印刷廠。

Thank you for your reading. I hope the above contents will be helpful to you. If you want to know more wonderful contents, please click our official website: Jinan printing factory.