手提袋是很多產品或類包裝會配的一個包裝部件，有了手提袋會讓人感覺整個產品更完整，那如何在設計階段做一個效果圖讓決策者提前感受下整個產品的終效果，而決定是否為這個產品做一個手提袋。
Handbags are a packaging component of many products or high-end packaging. With handbags, people will feel the whole product more complete. How to make an effect map at the design stage so that decision makers can feel the final effect of the whole product in advance, and decide whether to make a handbag for this product.
對于很多企業來說商業所用到的禮品，文件，書籍又或者自身產品都需要手提袋來盛放。手提袋可謂相當的適用，單一造價也不高。但是手提袋印刷在質量和品質上要求還是非常高，因此此類印品比較直觀展示公司相關信息，消費者直觀關注的正是我們手提袋印刷的內容，因此在印刷手袋的過程可能遇到的問題如下：
For many businesses, gifts, documents, books or their own products used in business need handbags to store. Handbags are quite suitable, and the single cost is not high. However, the quality and quality requirements of handbag printing are still very high. Therefore, this kind of printing can display the company's relevant information more intuitively. The most intuitive concern of consumers is the content of our handbag printing. Therefore, the problems that may be encountered in the process of printing handbags are as follows:
一、手提袋印刷采用的水墨都為純水性體系，不要將水墨與醇性墨和溶劑型油墨混合使用或在墨中加入有機溶劑，以免導致印刷質量問題。
First, the ink used in handbag printing is pure water-based system. Do not mix the ink with alcohol ink and solvent-based ink or add organic solvents in the ink, so as to avoid printing quality problems.
二、水墨的印刷適性受印刷條件、承印物的表面特性、環境溫濕度；水墨存放時間長短等客觀條件的影響，因此在使用水墨時，需要用一些助劑對水墨做細微調整以獲得佳印刷效果。
Secondly, the printability of ink is affected by the objective conditions such as printing conditions, the surface characteristics of the substrate, environmental temperature and humidity, and the length of storage time of ink. Therefore, when using ink, it is necessary to use some additives to fine-tune ink to obtain the best printing effect.
三、殘留在印刷設備上墨水盡量在未干燥前用清水沖洗干凈，無法用清水洗凈的墨可用清洗劑進行清洗。
3. Remaining ink on printing equipment should be washed with clean water as far as possible before drying. Inks that cannot be washed with clean water can be cleaned with detergent.
四、印刷過程中由于水的揮發作用，會導致水墨粘度升高和PH值下降，PH值應控制在8．5—9．5之間，若超出此范圍，可用PH穩定劑進行調節，保持粘度和PH值的穩定。
Fourth, the volatilization of water in printing process will lead to the increase of ink viscosity and the decrease of PH value. PH value should be controlled between 8.5 and 9.5. If it exceeds this range, PH stabilizer can be used to adjust it to maintain the stability of viscosity and PH value.
五、印刷剩余的墨水可以收回原裝桶里并將蓋子蓋嚴實，下次可重復使用。
5. The remaining ink from printing can be retrieved from the original barrel and tightly covered. It can be reused next time.
六、水墨適宜的儲存溫度是5℃—50℃攝氏度。
6. The optimum storage temperature for ink is 5-50 degrees Celsius.
七．稀釋劑：用于降低水墨的粘度。用量在3％以內不會降低水墨的顏色深度，并可保持水墨的PH值不變，加入較多的稀釋劑或使用硬度高的自來水稀釋會導致氣泡的產生，可同時加入消泡劑進行消泡。稀釋劑應邊攪拌邊緩慢加入，以防粘度過低。
Dilutants: Used to reduce the viscosity of ink. When the dosage is less than 3%, the color depth of the ink will not be reduced, and the PH value of the ink will remain unchanged. Adding more diluents or using high hardness tap water to dilute will lead to the formation of bubbles, and defoamer can be added to defoam at the same time. The diluent should be added slowly while stirring to avoid low viscosity.
八.慢干劑：用于降低水墨的干燥速度，用量在10％以內。
8. Slow drying agent: used to reduce the drying speed of ink, dosage less than 10%.
More information about Jinan handbag can be consulted by clicking on our official website: http://www.seven2000.com/
