In printing, the paper collecting system is related to the paper feeding system, positioning system, paper conveying system, water conveying ink system, paper collecting system, etc. How to solve the problem of uneven collection? As a Jinan album printing company, we summarize the following aspects:

　　1. 本文系統

　　1. This system

　　輸紙系統包括振蕩裝置、輸紙輥和鏈條。其標準狀態如下:

　　The paper conveying system includes an oscillating device, a paper conveying roller and a chain. The standard status is as follows:

　　擺動裝置。當凸輪在更小的擺動面上時，彈簧的張力略大，此時滾子與凸輪之間要保持20根鋼絲的間隙。擺動裝置與預卷紙輥連接時，牙墊之間的水平間距約為20根導線。

　　Swinging device. When the cam is on the minimum swing surface, the tension of the spring is slightly larger. At this time, the gap between the roller and the cam should be kept at 20 steel wires. When the swing device is connected with the pre roll roll, the horizontal space between the tooth pads is about 20 wires.

　　紙張傳輸系統功能單元。刁里的紙大約是2-4mm。雕的角度應大于450度。刁的前端應該是水平的。

　　Paper transfer system function unit. The paper in diaoli is about 2-4mm. The angle of carving shall be greater than 450 degrees. Diao's front end should be horizontal.

　　2. 給水系統

　　2. Water supply system

　　為了保證紙張的正常穩定，我們必須把握好以下幾點:壓紙腳——一定要平衡。紙堆正面低于整潔的紙塊2 ~ 3mm，吸紙嘴應吸紙到位，放紙應盡快退回。吸紙嘴在吸紙狀態下應降點，運轉平穩。壓腳、分離吸紙嘴、通過吸紙嘴與導紙輥的時間協調應處于標準狀態。

　　In order to ensure the normal stability of paper, we must grasp the following points: presser foot - must be balanced. The front side of the paper pile is 2 ~ 3mm lower than the clean paper block, the paper suction nozzle should be in place, and the paper should be returned as soon as possible. The paper suction nozzle shall be lowered to the lowest point in the paper suction state, and the operation shall be stable. The time coordination of presser foot, separating the paper suction nozzle and passing the paper suction nozzle with the first paper guide roller shall be in the standard state.

　　3.定位系統(GPS)

　　3. Positioning system (GPS)

　　定位系統包括前壓力計、點壓力計和側壓力計。他們的標準如下:

　　The positioning system includes front pressure gauge, point pressure gauge and side pressure gauge. Their criteria are as follows:

　　1)規則之前。兩個前規在同一水平線上，這樣每個單位的紙張傳輸系統之間的紙張傾角在2 ~ 4mm的范圍內。此時前規是固定的，不要隨意移動。

　　1) Before the rules. The two front gauges are on the same horizontal line, so that the paper inclination between each unit's paper transmission system is within the range of 2-4mm. At this time, the front gauge is fixed, do not move at will.

　　(2)電動牙。前量規下降，紙放到位。此時，電牙前端與紙張前端之間的距離約為1mm。

　　(2) Electric teeth. Lower the front gauge and put the paper in place. At this time, the distance between the front end of the electric tooth and the front end of the paper is about 1mm.

　　(3)側規。振蕩器只是用牙齒蘸著紙，而側規只是把紙壓起。此時，紙張應處于兩者的聯合控制下，且所提高的高度應大于450。

　　(3) side gauge. The oscillator just dips the paper with its teeth, while the side gauge just presses the paper up. At this time, the paper should be under the joint control of the two, and the maximum height raised should be greater than 450.

　　4. 沖壓系統

　　4. Stamping system

　　將印版滾筒和橡皮布滾筒洗凈，壓入熔絲后，測量被壓熔絲的厚度，兩輥之間的壓力厚度。

　　Clean the plate cylinder and blanket cylinder, press in the fuse, and measure the thickness of the pressed fuse and the pressure thickness between the two rollers.

　　5. 紙系統

　　5. paper system

　　(1)制版前后，前后左右的位置和印刷規格要對號;鏈條剛放紙，邊紙板剛搬出來;(3)吸輪吸紙后應穩定;后吸輪與下吸風口的間隙約為20根導線;(5)開球角度應在20左右;風輪的吸力從中間向兩邊遞減，以此類推。

　　(1) Before and after plate making, the front and rear positions and printing specifications should be numbered; the chain just put paper, and the edge cardboard just moved out; (3) the suction wheel should be stable after absorbing paper; the gap between the rear suction wheel and the lower suction port is about 20 wires; (5) the ball opening angle should be about 20; the suction force of the wind wheel decreases from the middle to both sides, and so on.

　　6. 給水油墨系統

　　6. Water supply ink system

　　(1)正常印刷時，墨輥上的油墨均勻而不大，細聽時油墨光滑無聲，印品較厚。

　　(1) In normal printing, the ink on the ink roller is uniform but not large. When listening carefully, the ink is smooth and silent, and the printed matter is thick.

　　要把握好水分，不要弄臟了印品，而且印件滿厚，越小越好。

　　To grasp the moisture, do not dirty the print, and print full thickness, the smaller the better.

　　以上是濟南畫冊印刷廠家為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://www.seven2000.comThe above is the related content introduced by Jinan album printing factory. If you want to know more, please visit the website: http://www.jingyinshua.com